Fodamon engineers share the differences between ball mill and rod mill as follows: 1. Appearance and structure The shape ratio of the barrels of the two mills is different. The ratio of the length and diameter of the rod mill barrel is generally 1.5-2, and the inner surface of the liner on the end cover is a vertical plane. There are various ...

Here a Rod Mill has its daily 3.5" steel rods being added using a mechanised rod mill charger. The operator only has a few minutes to load the rods and rest...

Rods in place weigh approximately 400 pounds per cu. ft. and balls in place approximately 300 pounds per cu. ft.. Thus, quantitatively, less material can progress through the voids in the rod mill grinding media than in the ball mill, and the path of the material is more confined. This grinding action restricts the volume of feed which passes ...

In all ore dressing and milling Operations, including flotation, cyanidation, gravity concentration, and amalgamation, the Working Principle is to crush and grind, often with rob mill & ball mills, the ore in order to liberate the minerals. In the chemical and process industries, grinding is an important step in preparing raw materials for subsequent treatment.

Ball mill and Rod mill is a tool used in modern mineral processing, coal chemical industry, sand making and other industries to grind ore into powder and then used in smelting industry to smelt gold, steel, etc. Coal chemical industry coal water slurry is gasified to make chemical raw materials, and sand making is used for glass or building sand. . There are still many uses, but do …

Ball mill： Ball mills are the most widely used one. Rod mill： The rod mill has the highest efficiency when the feed size is <30mm and the discharge size is about 3mm with uniform particle size and light overcrushing phenomenon. SAG mill: When the weight of the SAG mill is more than 75%, the output is high and the energy consumption is low ...

Ball mill and Rod mill is a tool used in modern mineral processing, coal chemical industry, sand making and other industries to grind ore into powder and then used in smelting industry to smelt gold, steel, etc. Coal chemical industry coal water slurry is gasified to make chemical raw materials, and sand making is used for glass or building sand. . There are still many uses, but do …

The finesse of the material milled by the ball mill is 0.074mm-0.4mm, only except for the two small ball mills that have a wider range of 0.075-0.89mm. However, the rod mill fine grinding fineness is about 0.833-0.147mm. In terms of the fineness of the ground material, the ball mill has a finer handling ability.

Rods in place weigh approximately 400 pounds per cu. ft. and balls in place approximately 300 pounds per cu. ft.. Thus, quantitatively, less material can progress through the voids in the rod mill grinding media than in the ball mill, and the path of the material is more confined. This grinding action restricts the volume of feed which passes ...

The ball mill is commonly divided into grid type ball mill and overflow type ball mill (named by the different discharging structure). The rod mill is divided into overflow type and open type rod mill, whose diameter of hollow shaft is generally larger …

Rod mills are used in an open circuit between crushing and the ball mill. They often operate in wet and where the pulp contains up to 50% solid by mass. This machine is equally very applicable to dry where it could take a feed that has achieved 6% moisture. As such, when the product is sticky, rod mills are preferred over ball mills.

Ball mill machine has always been the main grinding equipment in wet cement production. In the early years, the rod mill was first used in cement raw meal grinding, which increased the output of the grinding section by 31%, saved energy by 27%, and reduced the consumption of grinding media by 47%.

Typically R = 8. Rod Mill Charge: Typically 45% of internal volume; 35% – 65% range. Bed porosity typically 40%. Height of bed measured in the same way as ball mills. Bulk density of rods = 6.25 tons/m3. In wet grinding, the solids concentration 1s typically 60% – 75% by mass. A rod in situ and a cutaway of a rod mill interior.

Ball mill and rod mill are suitable for different materials. 1. Selection by material's hardness. Ball mill has a strong adaptation of material, and it is suitable for grinding hard materials, such as slag, iron ore, copper ore, etc. Rod mill is suitable for grinding brittle material, such as rare metals. 2.

Difference between rod mill and ball mill. 1.Grinding bodies work differently. We know that the rod mill is called a rod mill because its grinding medium is a steel rod, and the grinding medium of a ball mill is a steel ball. Due to the different shapes of the grinding bodies, their working methods also have their own characteristics.

The rod mill usually uses 50-100mm diameter steel rod as grinding medium, while the ball mill uses steel ball as grinding medium. The length of steel rod is 25-50mm shorter than the cylinder, and it is usually made of high carbon steel with carbon content of 0.8% – 1%; the loading capacity of rod is about 35% – 45% of the effective volume ...